Choosing a blade for your circular saw

Tradesperson fitting a saw blade on a cordless circular saw, with a second saw blade on the workbench

A circular saw cuts only as well as the blade fitted to it. A coarse blade cuts quickly through a beam, but frays the edge of a board. A fine blade gives a clean cut, but is slower and uses more battery. Below you can read which sizes have to match, how many teeth to choose and how to recognise a blunt blade.

First: the sizes have to match

Every saw blade shows two sizes, for example 165 x 20. They must match your tool exactly.

  • Diameter: the outside size of the blade. The DCK cordless circular saw uses 165 mm blades. A larger blade won't fit under the guard, a smaller blade gives less cutting depth.
  • Bore: the hole in the middle. On the DCK circular saw it is 20 mm. Some blades have a reducing ring to fit a smaller arbor. Only use a ring that fits exactly.
  • Maximum speed: the blade shows a maximum. It must be higher than the speed of your saw. The DCK circular saw runs at 5000 rpm no-load.

So if you are looking for a blade for the DCK circular saw, look for 165 x 20 mm.

How many teeth?

The number of teeth is the most important choice. Few teeth means big bites: fast and coarse. Many teeth means small bites: slower and neater.

Teeth (165 mm) Cut Use
16 to 24 Fast and coarse Beams, structural timber, ripping along the grain, reclaimed timber
36 to 40 All-round Sheet material, plywood, OSB, across and along the grain
48 to 56 Fine and clean Coated sheet material, laminate, furniture work, mouldings
48 or more, special tooth shape Fine, little heat Aluminium profiles, plastic (only with a blade suitable for this)

If you only have one blade, choose something around 24 to 40 teeth. That covers most work on site.

Tooth shape

The blade or packaging often shows an abbreviation for the tooth shape.

  • ATB (alternate top bevel, WZ): the teeth are bevelled alternately. They cut cleanly through wood fibres. Most used for wood and sheet material.
  • FT (flat top, FZ): straight-ground teeth. Fast and coarse, for ripping along the grain.
  • TCG (triple chip grind, TR): a trapezoid tooth alternating with a flat tooth. For hard materials such as laminate, coated board, aluminium and plastic.

For aluminium, also choose a blade with a negative or small hook angle. That stops the blade grabbing the material.

Thin kerf, longer battery life

On a cordless saw every watt counts. A blade with a thin kerf removes less material, so you cut more metres per charge. That is why many blades for cordless saws are thinner than blades for corded saws. Make sure the blade stays stable, though: too thin and it starts to vibrate.

How to recognise a blunt blade

  • You have to push harder than before.
  • Burn marks appear on the wood.
  • The saw pulls to one side or the cut is no longer straight.
  • The edges fray more than usual.
  • The battery runs flat faster.

A blunt blade costs battery and is more dangerous, because it binds more easily. Replace it or have it sharpened. Carbide blades can be resharpened a few times by a sharpening service.

How to change the saw blade

  1. Remove the battery from the saw.
  2. Press the spindle lock and loosen the bolt with the spanner supplied with the saw.
  3. Remove the flange and the old blade. Clean the flange.
  4. Fit the new blade with the arrow on the blade pointing in the same direction as the arrow on the guard.
  5. Refit the flange and tighten the bolt. Release the spindle lock and check that the blade turns freely.

A few tips for a clean cut

  • Set the cutting depth so that the blade protrudes 5 to 10 mm below the workpiece. That makes cutting faster and safer.
  • A circular saw cuts from the bottom up. So place the good side of a board face down.
  • Support the workpiece so that the cut falls open and doesn't pinch. That prevents kickback.
  • If you make a lot of straight cuts in board, use a guide or a straight edge with clamps.

You'll find the DCK cordless circular saw under Sawing. Saw blades and other accessories are under Accessories. Use a battery of 5.0 Ah or larger on the circular saw. The reason is explained in Which battery to choose.

Frequently asked questions

Does a 160 mm blade fit my 165 mm circular saw?

If the bore matches, it often fits. You then lose a few millimetres of cutting depth. Preferably stick to the size the manufacturer specifies.

Can I cut metal with my circular saw?

Only thin aluminium profiles, with a blade suitable for this. Do not cut steel with a wood circular saw.

How often should I replace a saw blade?

That depends on what you cut. Reclaimed timber with nails and coated sheet material blunt a blade faster than softwood. Replace it when you see the signs of a blunt blade.

Does the DCK circular saw come with a blade?

Yes, a 165 mm saw blade is included.