An angle grinder is a handy tool, but also one of the tools involved in the most accidents. The disc turns at thousands of rpm, and if it binds or breaks, things happen fast. The good news: a few fixed habits prevent almost all the risks. Below you can read what to wear, how to check the disc and how to prevent kickback.
What to wear
- Safety glasses or face shield. Always. Sparks, grinding dust and fragments of disc fly in all directions. For cutting and grinding, a face shield over your glasses is even better.
- Hearing protection. An angle grinder is loud, especially on metal and stone.
- Gloves. Close-fitting work gloves against sparks and sharp edges. No loose, oversized gloves that can get caught in the disc.
- Dust mask. Stone, concrete and tiles release silica dust. Wear a dust mask of at least FFP2, FFP3 for prolonged work.
- Workwear. Long sleeves that don't hang loose. No scarf, loose cords or open jacket. Tie back long hair.
- Safety shoes. In case something falls.
Checking the disc
Most accidents start with the disc. Check it every time you fit one.
- Diameter: only use the size your tool is made for, for example 125 mm.
- Speed: the maximum speed on the disc must be higher than the speed of your tool.
- Damage: don't use a disc with cracks or chipped edges, or a disc that has been dropped.
- Expiry date: resin-bonded grinding and cutting discs have a use-by date. It is on the metal ring in the centre. An expired disc can break.
- The right disc for the job: a cutting disc is for cutting straight through, not for grinding with the side. Use a grinding disc for that.
Never use a toothed saw blade, such as a wood saw blade, on an angle grinder. The risk of kickback is high.
Guard and side handle
The guard must always be fitted. Position it so it sits between you and the disc, so sparks and fragments go away from you. Never remove it to get a better view.
Fit the side handle and always work with two hands. That way you keep hold of the tool if it suddenly jerks. The handle fits left or right; choose the side that suits your working position.
Before you start
- Check the tool, the cable or the battery for damage.
- Secure the workpiece with clamps or in a vice. Never hold it by hand.
- Check what is behind and under the workpiece: pipes, cables, flammable material.
- Let a new disc run without load for half a minute first, pointing away from you. If it vibrates or makes a strange noise, stop and replace it.
Preventing kickback
Kickback happens when the disc binds or jams. The tool then shoots forcefully towards you or upwards. How to prevent it:
- Support the workpiece so the cut opens up while grinding rather than pinching shut.
- With a cutting disc, only cut in a straight line. Don't make curves.
- Don't push too hard. Let the disc do the work.
- Don't stand directly behind the tool, but slightly to the side of the cutting line.
- Don't switch the tool on while the disc is touching the workpiece.
Sparks and fire
When grinding metal, glowing particles fly several metres. Remove flammable materials or cover them. Watch out for sawdust, paint tins, gas bottles and dry leaves. After the work, check the area once more for smouldering remains.
After grinding
- Let the disc come to a complete stop before you put the tool down.
- Don't put the tool down with the disc facing downwards.
- Keep your hands off the workpiece and the disc: they are hot.
Changing a disc
- Remove the battery, or unplug the tool.
- Press the spindle lock and loosen the clamping nut with the pin spanner.
- Remove the old disc and check the flange.
- Fit the new disc on the spindle. Make sure the clamping nut is the right way round: with thin cutting discs it often goes on differently than with thick grinding discs. Check the manual.
- Tighten the clamping nut with the spanner. Release the spindle lock before switching the tool on.
If the disc is stuck and the nut won't come loose, don't use a hammer or pliers. That damages the spindle and the lock.
Battery or mains: take note
- Battery: always remove the battery when changing the disc. Refitting a battery with the switch in the on position is dangerous without restart protection.
- Mains: keep the cable behind you and away from the disc. Use an extension reel that is fully unwound.
Which angle grinder suits you is explained in How to choose the right angle grinder. You'll find the tools under Grinding, and discs and accessories under Accessories. Read about CE marking and manuals on CE and product safety.
Frequently asked questions
Can I grind without the guard?
No. The guard catches sparks and fragments of a breaking disc. Always work with the guard fitted.
Which dust mask do I need for tiles and concrete?
At least FFP2, FFP3 for prolonged work. Work outdoors or with extraction where possible.
How do I know if a disc has expired?
The metal ring in the centre of the disc shows a date. After that date, don't use the disc any more.
Can I fit a bigger disc on my grinder?
No. A bigger disc doesn't fit under the guard and turns too fast at the edge. Only use the size that belongs to your tool.